Click image to view full size image
Description:
1. Brushless motor .
2. New regulator system , the output is more stable
RongPeng New Product High Pressure Airless Paint Sprayer- 480N:
| Model No | 480N |
| Pressure | 220 ± 10% |
| Electric current | 2-4A |
| Frequency | 50HZ |
| Motor rated power | 882W |
| Max. Pressure | 3300PSI |
| Flow Rate | 2.1L/min |
| Standard Nozzle | 517/723 |
| Length of high pressure hose | 15m |
| Max. Pressure for the hose | 93Mpa |
Airless Paint Sprayer Trouble Shooting:
| Airless paint sprayer's motor doesn't work | 1.The power supply is not connected or bad contact. 2.Pressure setting is too low 3.Carbon brush damage or bad contant. 4.The airless paint spray's motor damage 5.Switch damage 6.Equipment overload, Circuit board damage
| 1.Check circuit 2.Improve the power to be more higher 3.Change the carbon or check the carbon brush. 4.Change the damage 5.Change the switch 6.Change te circuit
|
| Airless paint sprayer's equipment not to absorb material | 1.There is some air in the pipeline 2.Feed valve catch up the steel ball
| 1.Check the pipe and open the decompression valve 2.Dismounting cleaning
|
| There is no flow or too low | 1.No paint supply 2.Feed pipe blockage 3.Gun clogging 4.Paint viscosity is too high
| 1.check the paint bucket 2.Clean the feed pipe 3.Check and clean the body 4.Dilution coating
|
| The airless paint sprayer's equipment can not keep pressure | 1.Equipment leak 2.Feed pipe leak 3.Feed part ball wea or jam 4.Open closed valve wear or jam 5.Seal ring wear 6.Feed seat wear 7.Opening and closing the valve seat wear
| 1.Tightening the equipment parts 2.Tightening and check the feed pipe 3.Replacement or clean 4.Replacement or clean 5.Replacement 6.Replacement 7.Replacement
|
| The airless paint sprayer's pressure is not enough | 1.Pressure set too low 2.Jam 3.Nozzle is too big or wear
| 1.Increase the pressure 2.Clean 3.Replacement
|
| The airless paint sprayer's Spray gun abnormal vibration | 1.Nozzle is too big or wear 2.The pressure is too high
| 1.Replacement the nozzle 2.Decrace the pressure
|
| Coating leak put | 1.There is some air in te equipment 2.There is some dirt in the spray gun 3.The spray gun‘s seal ring wear
| 1.Check 2.Clean the nozzle 3.Replacement the seal
|
| The spraying gun can't stop discharging | 1.Needleor esal ring wear 2.There is some dirt in the spray gun
| 1.Replacement the seal ring 2.Clean the spray gun
|
| The spraying gun do not disarge | 1.There is no paint supply int the airless paint spray. 2.Nozzle jam 3.Filter clogging
| 1.Check the airless paint spray 2.Reverse clean th e nozzle 3.Clean the filter
|
| Spraying speanappear the trailing | 1.Spraying underpressure 2.Coating can't completely atomization 3.Coating velocity is not enough 4.Paint viscosity is too high 5.Nozzle wear
| 1.Increase the pressure 2.Replacement a smaller nozzle 3.Clean the spray gun, equipment 4.Reduce paint viscosity
|
| Spraying spean is not iniformity | 1. Airless paint sprayer's nozzle is too big
| 1.Replacement the airless paint sprayer's nozzle
|
| Intermediate too thick | 1.There is some gap on the nozzle
| 1.Replacement the airless paint sprayer's nozzle
|
| Spraying span slanting one side | 1. Airless paint sprayer's nozzle jam or wear
| 1.Replacement or clean the airless paint sprayer's nozzle
|
| Spraying spn(waxes and wanes) | 1.Suction feeding tube drit 2.Suction feeding tube use method error 3.Nozzle is too big or wear
| 1.Check an tightening 2.Correct use of the suction feeding tube 3.Replace the nozzle
|
Showroom:
Certificate :
Airless paint spray packaging and eqipment:
RongPeng New Product High Pressure Airless Paint Sprayer- 480N
